Pushbutton switch AP｜NIDEC COMPONENTS EUROPE GmbH

Pushbutton switch AP

●Um einen Kauf zu tätigen, wenden Sie sich an die Verteiler unten.
Verkaufskanal Überprüfen Sie die Verteiler.: VERKAUFSKANALKlicken Sie hier, um den Verteiler zu überprüfen.

Subminiature Pushbutton Switches

A part of this series was discontinued Check affected part number

FeaturesFeatures

Gold-plated contacts.
Terminal pin pitch: 2.54 mm.

Specifications

Rating	Max:50mA 48VAC/DC Min:1μA 20mVAC/DC
Initial contact resistance	50mΩ max.(1.5mA 200μVAC)
Dielectric strength	500VAC 1 minute
Insulation resistance	10,000MΩ min.(250VDC)
Electrical life	10,000 operations at maximum rating. 50,000 operations at 0.4VA.
Operating temperature range	－20～＋85℃
Storage temperature range	－40～＋85℃

Part Number Designation

A	P	1	C -	2	M	- 10 - Z
Series	Actuator type P: Pushbutton (Non-washble)	No. of poles 1: 1 pole 2: 2 poles	SW function C or M: Off-(On) F or R: On-(On)	Terminals 2: PC straight 6: R/A 0.3" pitch	Actuator shape M: Standard S: Short H: Square	Clip mechanism

C -

- 10 - Z

Series

Actuator type

Pushbutton
(Non-washble)

No. of poles

1 pole

2 poles

SW function

C or M:

Off-(On)

F or R:

On-(On)

Terminals

2: PC straight

R/A 0.3" pitch

Actuator shape

Standard

Short

Square

Clip mechanism

List of Part Numbers

※

A part number indicated with a gray-back in the list below was discontinued with an order deadline of Dec. 20, 2023.

Part No.	No. of poles	SW function	Terminals	Actuator shape	CAD
Part No.：AP1C-2H-Z	1 pole	OFF-(ON)	PC straight	Square	3D CAD（Any Model）
Part No.：AP1C-2S-Z	1 pole	OFF-(ON)	PC straight	Short	3D CAD（Any Model）
Part No.：AP1C-2M-Z	1 pole	OFF-(ON)	PC straight	Standard	3D CAD（Any Model）
Part No.：AP1F-2M-Z^☆	1 pole	ON-(ON)	PC straight	Standard	3D CAD（Any Model）
Part No.：AP1F-2S-Z	1 pole	ON-(ON)	PC straight	Short	3D CAD（Any Model）
Part No.：AP1F-2H-Z	1 pole	ON-(ON)	PC straight	Square	3D CAD（Any Model）
Part No.：AP2R-2M-Z^★	2 poles	ON-(ON)	PC straight	Standard	3D CAD（Any Model）
Part No.：AP1C-6M-Z	1 pole	OFF-(ON)	R/A 0.3" pitch	Standard	3D CAD（Any Model）
Part No.：AP1C-6S-Z	1 pole	OFF-(ON)	R/A 0.3" pitch	Short	3D CAD（Any Model）
Part No.：AP1F-6S-Z	1 pole	ON-(ON)	R/A 0.3" pitch	Short	3D CAD（Any Model）
Part No.：AP1F-6M-Z^★	1 pole	ON-(ON)	R/A 0.3" pitch	Standard	3D CAD（Any Model）
Part No.：AP2M-6S-Z^★	2 poles	OFF-(ON)	R/A 0.3" pitch	Short	3D CAD（Any Model）
Part No.：AP2M-6M-Z^☆	2 poles	OFF-(ON)	R/A 0.3" pitch	Standard	3D CAD（Any Model）
Part No.：AP2R-6M-Z^★	2 poles	ON-(ON)	R/A 0.3" pitch	Standard	3D CAD（Any Model）
Part No.：AP2R-6S-Z^☆	2 poles	ON-(ON)	R/A 0.3" pitch	Short	3D CAD（Any Model）
Part No.：AP1F-6S-Z	1 pole	ON-(ON)	R/A 0.3" pitch	Short	3D CAD（Any Model）
Part No.：AP1F-6M-Z^★	1 pole	ON-(ON)	R/A 0.3" pitch	Standard	3D CAD（Any Model）
Part No.：AP2M-6S-Z^★	2 poles	OFF-(ON)	R/A 0.3" pitch	Short	3D CAD（Any Model）
Part No.：AP2M-6M-Z^☆	2 poles	OFF-(ON)	R/A 0.3" pitch	Standard	3D CAD（Any Model）
Part No.：AP2R-6M-Z^★	2 poles	ON-(ON)	R/A 0.3" pitch	Standard	3D CAD（Any Model）
Part No.：AP2R-6S-Z^☆	2 poles	ON-(ON)	R/A 0.3" pitch	Short	3D CAD（Any Model）

☆: Semi-standard products /
★: Made to order products

Soldering Specifications

Manual Soldering
Device：Soldering iron
①380°C, Max.; 3 seconds, Max.
Auto Soldering (PC types only)
Device：Jet wave type or dip type
①275°C, 6 seconds, Max.
Pre-heating should be done at temperatures from 80 to 120°C and within 120 seconds.
When soldering two or more terminals to the common land, use solder resist to solder them independently.

Flux Cleaning

Solvent :Fluorine or Alcohol type
The AP series are not washable. To wash the PC board, clean the soldering surface of the PC board with a brush so that the switch is not exposed to the cleaning solution.