NIDEC COMPONENTS logo
NIDEC COMPONENTS logo

LIST

×

×


Products

Distributor

Global-En

×

Pushbutton switch APE

●To buy this product, please go to the following Online Web stores.
To the Pushbutton switch “APE series” page on the DigiKey online shop
To the Pushbutton switch “APE series” page on the Chip1stop online shop
To the Pushbutton switch “APE series” page on the Farnell online shop
To the Pushbutton switch “APE series” page on the Mouser online shop

Subminiature Pushbutton Switches

 
FeaturesFeatures
  • Twin-contact clip mechanism for high reliability.

  • Process sealed structure

  • Gold-plated contacts.

  • Terminal pin pitch: 2.54 mm.

  • UL recognized

Specifications

Rating 0.4VA AC/DC
Max:50mA 60VAC/DC
Min:1μA 20mVAC/DC
UL:48VAC/DC 50mA
Initial contact resistance 50mΩ max.(1.5mA 200μVAC)
Dielectric strength 250VAC 1 minute
Initial Insulation resistance 500MΩ min. (500VDC)
Electrical life 10,000 operations at maximum rating.
30,000 operations at 0.4VA
Operating force 0.78±2.94N
Operating temperature range -20~+85℃
Storage temperature range -40~+85℃

Part number designation

APE2F-2M-10-Z

Series code

Actuator shape

PE:Washing push type

Number of poles

1:1pole
2:2poles

Switching function

F: ON -( ON)

Terminal style

2: PC Straight
5: Right angle
(0.2 inch pitch)

6:Right angle
(0.3 inch pitch)

Actuator shape

M: Standard

Clip contact mechanism

 

List of part numbers

Part numberNumber of polesSwitching functionTerminal styleActuator shapeCAD
APE1F-2M-10-Z 1pole ON -(ON) PC Straight Standard
APE2F-2M-10-Z 2poles ON -(ON) PC Straight Standard
★APE1F-5M-10-Z 1pole ON -(ON) Right angle(0.2 inch pitch) Standard
APE1F-6M-10-Z 1pole ON -(ON) Right angle(0.3 inch pitch) Standard
☆APE2F-6M-10-Z 2poles ON -(ON) Right angle(0.3 inch pitch) Standard

☆:Semi-standard products. ★:Made to order products

Mounting of Switch

  • Use PC boards with hole diameter of 1mm.
  • Do not bend the terminal pins before mounting the switch on the PC board.
  • After mounting the switch, do not place the device in such a way that the device weight will be applied on to the actuator of the switch.
  • Do not apply load exceeding 12.7 N to the actuator.
    If load exceeding 12.7 N is expected to be applied to the actuator, please use a Bracket (optional accessory sold separately).
    Maximum load will be 29.4 N when a Bracket is used.
  • Use Bracket 140000640314 or 140000640318 for side-byside mounting.
  • To instance mounting strength, use bracket 140000640315.
  • PC Hole Layouts will change depending on the Bracket.

Soldering Specifications

  • Manual Soldering
    Device:Soldering iron
    380°C, Max.; 3 seconds, Max.
  • Auto Soldering
    Device:Jet wave type or dip type
    275°C, Max.; 6 seconds, Max.
    ・Pre-heating should be done at temperatures ranging from 80°C to 120°C and within 120 seconds.

Flux Cleaning

  • Solvent :Fluorine or Alcohol type.
  • Cleaning after soldering should be done after the terminal temperature falls to 90℃ or below, or after leaving the
    switch for five minutes or longer at room temperature.
  • Do not use ultrasonic cleaning.

Environmental Data

●The above contents and descriptions are subject to change without notice. 

Products

×

page top