NIDEC COMPONENTS logo
NIDEC COMPONENTS logo

LIST

×

×


Products

Distributor

EU-English

×

Pushbutton switch 8W-N

Snap-in Pushbutton Switches

 
FeaturesFeatures
  • The 8W Snap-in Pushbutton switch is an 8R Soft Touch Pushbutton switch with a 12 mm square button and a

    mounting frame.
  • The panel cut-out dimensions are the same as the 8H series Lever & Rocker switcheswhich enables side-by-side mounting.

  • Buttons and mounting frames are available in 4 colors.

  • Silver or gold-plated contacts

  • Epoxy resin case UL94V-0 self-extinguishing epoxy.

  • Insulation between terminal and ground: 4 mm minimum. 

  • Prevention of flux entry The epoxy resin seal on bottom of the switch helps prevent short-circuiting between poles ensuring high reliability

  • Insulation barrier: Insulation barrier design between poles helps prevent short-circuiting between poles ensuring high reliability.

Specifications

Rating Silver plated:3A 125VAC (Resistive load)
Gold plated :60mA 30VDC max. (Resistive load)
Initial contact resistance Silver plated:10mΩ max.(1A 2~4VDC)
Gold plated:20mΩ max.(5mA 200μVAC)
Initial dielectric strength 1,000VAC 1 minute
Initial insulation resistance 1,000MΩ min. (500VDC)
Electrical life 25,000 operations(50,000 operations:Gold plate)
Operating temperature range -20℃~+85℃
Storage temperature range -40℃~+85℃
Operating force 8W102■-N-Z:2.94±0.98N
8W202■-N-Z:4.9±1.96N

Part Numbering

8 W 1 01 1 B - Z
Series code


Actuator shape
N:Standard
P:Splash proof
Y:Mustang
R:Soft Touch
W:Snap-in
Number of poles
1: 1
2: 2
Switching function
01: ON-ON
02: ON-(ON)
Terminal style
1: Solder
2: PC/Straight
Contact material /Plating
None:Bs+Ag or Cu+Ag/Ag
B: Bs or Cu/Ni+Au
C:Bs+Ag or Cu+Ag/Ni+Au
 


Note :Some combinations may not be available. Please check the "Tableof Part Numbers" for each series.

List of part numbers

Part NumberNumber of polesSwitching functionTerminal styleCAD
8W1021-N-Z 1pole ON -( ON) Solder
★8W2021-N-Z 2poles ON -( ON) Solder
★8W1022B-N-Z 1pole ON - ON PC Straight

 

Terminal Styles

PC Hole Layouts

Panel Cut-Out Dimensions

Panel thickness(with Mounting Frame) : 1 mm to 2.5 mm

ボタン、取付枠の取付方法

※Specify part number of Button and Mounting Frame when ordering.

Standard Accessories

 ※Please specify the Button and the Mounting Frame when ordering.

Soldering Specifications

  1. Manual soldering
    Device:Solder iron
    ①420℃ Max. 3 sec. Max.
  2. Auto soldering
    ②The above-stated soldering conditions shall apply only to switches with straight terminals. Auto soldering is not possible with right-angle terminals.
    Switches with right-angle terminals should be soldered manually according to the conditions specified in (1) above.
  3. When putting the switches through an aging process after they were soldered onto the printing board or after installed into a complete end product, be sure to remove the buttons ofthe switches.,

Mounting

  • Do not bend the terminals before mounting the switch on the PC board.
  • After mounting the switch, do not place the device in such a way that the device weight will be applied on to the actuator of the switch.
  • For switches with straight terminals, solder the switch on the PC board after fixing the switch on the panel with a nut.

Flux Cleaning

  • Solvent : Fluorine or Alcohol type.
  • 8A/B/C/D/E/F/J/S series are not washable. To wash the PC board, clean the soldering surface of the PC board
    with a brush so that the switch is not exposed to the cleaning solution.

UL-Recognized, CSA certified Products

 

Environmental Data

●The above contents and descriptions are subject to change without notice. 

Products

×

page top