Toggle switch 8C｜NIDEC COMPONENTS CORPORATION

Toggle switch 8C

A part of this series was discontinued Check affected part number

FeaturesFeatures

The 8C series has a fl atted actuator and is anti-rotation.. The dress nut is standard with the fl atted toggle.
Suitable for applications where panel space is limited and a larger toggle is needed.
Terminal style : Solder, Straight, Right angle and vertical mount PC terminals. Contacts : Silver or gold.
Epoxy resin case : UL94V-0 self-extinguishing epoxy.
Actuator styles : Over 30 actuator variations.
Insulation between terminal and ground : 4 mm minimum. Prevention of flux entry The epoxy resin seal on bottom of the switch helps prevent the entry of solder and flux.
Insulation barrier : Insulation barrier design between poles helps prevent short-circuiting between poles ensuring high reliability.
UL Recognized product File No.E43275 CSA Certified product File No.LR38341

8	C	1	01	1		- Z
Series	Actuator shape C: Flatted toggle	No. of poles 1: 1 pole 2: 2 poles 3: 3 poles	Switching function 01: ON-ON 02: ON-OFF-ON 04: (ON)-OFF-(ON)	Terminal style 1: Solder 2: PC straight	Contact material / Plating Blank: Bs+Ag or Cu+Ag / Silver plated (Ag) / Silver plated (Ag) Bs=Brass, Ag=Silver, Cu=Copper

- Z

Series

Actuator shape

C: Flatted toggle

No. of poles

1: 1 pole

2: 2 poles

3: 3 poles

Switching function

01: ON-ON

02: ON-OFF-ON

04: (ON)-OFF-(ON)

Terminal style

1: Solder

2: PC straight

Contact material / Plating

Blank:

Bs+Ag or Cu+Ag / Silver plated (Ag)

/ Silver plated (Ag)

Bs=Brass, Ag=Silver, Cu=Copper

※

A part number indicated with a gray-back in the list below was discontinued with an order deadline of Dec. 20, 2023.

Part No.	No. of poles	Terminals	SW functions	CAD
Part No.：8C1011-Z	1 pole	Solder	ON－ON	3D CAD（Any Model）
Part No.：8C1021-Z^★	1 pole	Solder	ON－OFF－ON	3D CAD（Any Model）
Part No.：8C1041-Z^★	1 pole	Solder	(ON)－OFF－(ON)	3D CAD（Any Model）
Part No.：8C1012-Z^☆	1 pole	PC straight	ON－ON	3D CAD（Any Model）
Part No.：8C2011-Z	2 poles	Solder	ON－ON	3D CAD（Any Model）
Part No.：8C2021-Z^★	2 poles	Solder	ON－OFF－ON	3D CAD（Any Model）
Part No.：8C2041-Z^★	2 poles	Solder	(ON)－OFF－(ON)	3D CAD（Any Model）
Part No.：8C3011-Z^☆	3 poles	Solder	ON－ON	3D CAD（Any Model）

☆: Semi-standard products /
★: Made to order products

Rating Max.	Silver Contact: 125 VAC 6 A / 250 VAC 3 A / 30 VDC 4 A Gold Contact: 125 VAC 6 A / 250 VAC 3 A / 20 VDC 25 mA
Initial contact resistance	Silver Contact: 10 mΩ Max. (2~4 VDC 1 A） Gold Contact: 20 mΩ Max. (200 μVAC 1.5 mA）
Initial dielectric strength	1500 VAC 1 minute
Initial insulation resistance	1000 MΩ Min. (500 VDC)
Electrical life	Alternate type: 50,000 cycles Momentary type: 25,000 cycles
Operating temperature range	ｰ30 ~ +85 ℃
Storage temperature range	ｰ40 ~ +85 ℃

Manual soldering/Device ：Solder iron ①420℃ Max. 3 sec. Max.
Auto soldering/275℃ Max. 6 sec. Max.
The above-stated soldering conditions shall apply only to switches with straight terminals. Auto soldering is not possible with right-angle terminals. Switches with right-angle terminals should be soldered manually according to the conditions specifi ed in (1) above.
When soldering two or more terminals to the common land, use the solder resist to isolate the terminals.。

Solvent : Fluorine or Alcohol type.
8A/B/C/D/E/F/J series are not washable. To wash the PC board, clean the soldering surface of the PC board with a brush so that the switch is not exposed to the cleaning solution.
Cleaning after soldering should be done after the terminal temperature falls to 90℃ or below, or after leaving the switch for fi ve minutes or longer at room temperature.

Do not bend the terminals before mounting the switch on the PC board.
After mounting the switch, do not place the device in such a way that the device weight will be applied on to the actuator of the switch.
For switches with straight terminals, solder the switch on the PC board after fi xing the switch on the panel with a nut.